WelcomeWelcome | FAQFAQ | DownloadsDownloads | WikiWiki

Author Topic: eGalax touch screen  (Read 19192 times)

Offline Tuftec

  • Full Member
  • ***
  • Posts: 111
Re: eGalax touch screen
« Reply #15 on: May 01, 2011, 10:36:13 PM »
So this is want the /proc/bus/......  file looks like.

Offline Juanito

  • Administrator
  • Hero Member
  • *****
  • Posts: 14788
Re: eGalax touch screen
« Reply #16 on: May 01, 2011, 11:14:24 PM »
If that's all of it, it doesn't look like your touch screen is detected.

If you load the usb-utils extension, what does "lsusb" show?
« Last Edit: May 01, 2011, 11:16:36 PM by Juanito »

Offline Tuftec

  • Full Member
  • ***
  • Posts: 111
Re: eGalax touch screen
« Reply #17 on: May 02, 2011, 12:18:30 AM »
Yep.
It looks like the touch screen is not showing up correctly.
How do I use usbutils?


Offline Juanito

  • Administrator
  • Hero Member
  • *****
  • Posts: 14788
Re: eGalax touch screen
« Reply #18 on: May 02, 2011, 12:24:20 AM »
How do I use usbutils?

Install the usb-utils extension and use the command "lsusb"

Offline Tuftec

  • Full Member
  • ***
  • Posts: 111
Re: eGalax touch screen
« Reply #19 on: May 02, 2011, 01:29:22 AM »
This is what lsusb gives.

Offline Tuftec

  • Full Member
  • ***
  • Posts: 111
Re: eGalax touch screen
« Reply #20 on: May 02, 2011, 01:40:09 AM »
I get these messages for the USB port with the touch screen controller connected.

usb 3-1: new low speed USB device using ohci_hcd and address 5
generic-usb: probe of 0003:0EEF:0001.0004 failed with error -32
usbcore: registered new interface driver usbtouchscreen

What does this mean?


Offline Tuftec

  • Full Member
  • ***
  • Posts: 111
Re: eGalax touch screen
« Reply #21 on: May 02, 2011, 01:41:14 AM »
The messages are from dmesg.

Offline Juanito

  • Administrator
  • Hero Member
  • *****
  • Posts: 14788
Re: eGalax touch screen
« Reply #22 on: May 02, 2011, 01:51:32 AM »
This is what lsusb gives.

Code: [Select]
Bus 003 Device 002: ID 0eef:0001 D-WAV Scientific Co., Ltd eGalax TouchScreen
It seems the touch screen is at least recognised, you can get more details (though I don't know if that will add anything) using "lsusb -vv"

Offline Juanito

  • Administrator
  • Hero Member
  • *****
  • Posts: 14788
Re: eGalax touch screen
« Reply #23 on: May 02, 2011, 01:55:12 AM »
I wonder if you need a "waitusb=10" or similar on boot to allow the touchscreen time to start correctly?

Offline Tuftec

  • Full Member
  • ***
  • Posts: 111
Re: eGalax touch screen
« Reply #24 on: May 02, 2011, 02:55:13 AM »
I have waitusb=15 set.
I am not sure that is the problem.
I can try waitusb=30 or so to see what happens.

The problem (error messages) show up when you plug the touchscreen in with the system running. Not just on boot up. Does waitusb influence this as well as at boot?


Offline Juanito

  • Administrator
  • Hero Member
  • *****
  • Posts: 14788
Re: eGalax touch screen
« Reply #25 on: May 02, 2011, 02:58:02 AM »
I have waitusb=15 set.
I am not sure that is the problem.
I can try waitusb=30 or so to see what happens.
I'd say 15 seconds is already more than enough

Quote
The problem (error messages) show up when you plug the touchscreen in with the system running. Not just on boot up. Does waitusb influence this as well as at boot?
No, waitusb is only for the initial boot.

I wonder if the usb interface of your touchscreen is buggy or defective - is there a firmware update or similar available?

Offline tinypoodle

  • Hero Member
  • *****
  • Posts: 3857
Re: eGalax touch screen
« Reply #26 on: May 02, 2011, 04:23:11 AM »
As the device seems to be recognized despite error output, you could still proceed with configuring and running gpm and just see what will happen   ;)
"Software gets slower faster than hardware gets faster." Niklaus Wirth - A Plea for Lean Software (1995)

Offline Tuftec

  • Full Member
  • ***
  • Posts: 111
Re: eGalax touch screen
« Reply #27 on: May 02, 2011, 04:37:23 AM »
I tried that, but GPM (as from the TC repository) does not seem to respond to all the necessary command line options (like -R) it throughs up an error.
Maybe I am doing something wrong?

Offline smultita

  • Newbie
  • *
  • Posts: 13
    • EmbLin
Re: eGalax touch screen
« Reply #28 on: May 02, 2011, 03:37:38 PM »
try: sudo evtest /dev/input/eventX
and check the events, if they report under type 3 (absolute) you could use
http://forum.tinycorelinux.net/index.php?topic=9146.msg51729#msg51729

Offline Tuftec

  • Full Member
  • ***
  • Posts: 111
Re: eGalax touch screen
« Reply #29 on: May 02, 2011, 06:10:48 PM »
I tried evtest, but the touchscreen does not appear to show up in the list.