General TC > General TC Talk

Get APPS with no internet on TC laptop? Load APS on boot from auto-mounted USB?

<< < (13/28) > >>

Juanito:
Once "lsmod" shows that the "rtl8187" module has been loaded, can you post the output of "dmesg | tail -25" here.

This should show which network interface has been assigned to your wireless hardware.

grandma:
New laptop DRIVE is screwed -  need syslinux.tcz, beaver2, perl (which I have) and dosfstools - which I have - is there a url to get these so I can install, get that drive up (currently partiontion is hosed - I dusted Windows 7 - just smoked it with a DEL - felt real good too  ;D )

Juanito:
http://distro.ibiblio.org/pub/linux/distributions/tinycorelinux/3.x/tcz/syslinux.tcz
http://distro.ibiblio.org/pub/linux/distributions/tinycorelinux/3.x/tcz/glib1.tcz
http://distro.ibiblio.org/pub/linux/distributions/tinycorelinux/3.x/tcz/gtk1.tcz
http://distro.ibiblio.org/pub/linux/distributions/tinycorelinux/3.x/tcz/beaver.tcz

How about the output from "dmesg | tail -25" on your other machine?

grandma:
My mistake - I forget to get the dmesg - just a sec...

OK - here we go

eth0:  setting half-duplex.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0x100-0x3af:
intel_rng: FWH not detected
 clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0x3e0-0x4ff: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0x820-0x8ff: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0xc00-0xcf7: clean.
pcmcia_socket pcmcia_socket1: cs: IO port probe 0xa00-0xaff: clean.
cfg80211: Using static regulatory domain info
cfg80211: Regulatory domain: 00
    (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
    (2457000 KHz - 2482000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
    (2474000 KHz - 2494000 KHz @ 20000 KHz), (600 mBi, 2000 mBm)
    (5170000 KHz - 5250000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
    (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 2000 mBm)
cfg80211: Calling CRDA to update world regulatory domain
phy0: Selected rate control algorithm 'pid'
phy0: hwaddr 00:40:0c:00:41:d1, RTL8187vB (default) V1 + rtl8225z2, rfkill mask 2
rtl8187: Customer ID is 0x00
Registered led device: rtl8187-phy0::radio
Registered led device: rtl8187-phy0::tx
Registered led device: rtl8187-phy0::rx
rtl8187: wireless switch is on
usbcore: registered new interface driver rtl8187

Juanito:
Hmm - strange that the "rtl8187" is registered as loaded, but it does not give a network interface.

What does "iwconfig" show?

Navigation

[0] Message Index

[#] Next page

[*] Previous page