WelcomeWelcome | FAQFAQ | DownloadsDownloads | WikiWiki

Author Topic: Boot Core with ntfs-3g extension  (Read 16347 times)

Offline casey

  • Newbie
  • *
  • Posts: 34
Re: Boot Core with ntfs-3g extension
« Reply #30 on: October 30, 2013, 07:58:07 PM »
I'm an old programmer (since the days of dos)

I need a basic command line to start my software from a CD or pen drive, on all computers directly through the bios, without needing Windows or other operating systems

also using a distro oriented should modify it to make it a command line with ntfs support and mount all drives

and use tiny core because preparing it with your help, will help me to learn a lot about Linux

I know many linux commands, use the command line very well, but I do not know how to configure/prepare and compile, for this I would like to learn

Offline gerald_clark

  • TinyCore Moderator
  • Hero Member
  • *****
  • Posts: 4254
Re: Boot Core with ntfs-3g extension
« Reply #31 on: October 30, 2013, 08:08:50 PM »
What software is it you want to run?
Why do you need ntfs?
Why do you want to mount all drives?
Without a clear definition of the goal, it is difficult to give recommendations.

Offline casey

  • Newbie
  • *
  • Posts: 34
Re: Boot Core with ntfs-3g extension
« Reply #32 on: October 30, 2013, 08:36:04 PM »
I'm designing a software that boots from CD to repair a windows system not functioning properly, and to make backups of personal data on external hdd

I need to see all the drives and access to drive ntfs

Offline gerald_clark

  • TinyCore Moderator
  • Hero Member
  • *****
  • Posts: 4254
Re: Boot Core with ntfs-3g extension
« Reply #33 on: October 30, 2013, 08:55:56 PM »
There are CDs for this already. To name a few:
System Rescue CD
Recovery is Possible
Ultimate Boot CD

And by the way, automounting your damaged filesystem is a really bad idea.
« Last Edit: October 30, 2013, 09:01:40 PM by gerald_clark »

Offline tinypoodle

  • Hero Member
  • *****
  • Posts: 3857
Re: Boot Core with ntfs-3g extension
« Reply #34 on: October 30, 2013, 09:11:11 PM »
If you want to edit files for UNIX-like operating systems under windows, then you must always run 'dos2unix' on them, this is not even particular to Linux.
"Software gets slower faster than hardware gets faster." Niklaus Wirth - A Plea for Lean Software (1995)

Offline casey

  • Newbie
  • *
  • Posts: 34
Re: Boot Core with ntfs-3g extension
« Reply #35 on: October 30, 2013, 09:24:29 PM »

Gerald_clark
I have to create this program, which will be fully automated for my clients,

linux distro for recovery are another matter, that have nothing to do with my program

I asked for help to mount all drives and add the ServerX to my mini-iso

you're making me the third degree without help

Offline casey

  • Newbie
  • *
  • Posts: 34
Re: Boot Core with ntfs-3g extension
« Reply #36 on: October 30, 2013, 09:30:18 PM »
If you want to edit files for UNIX-like operating systems under windows, then you must always run 'dos2unix' on them, this is not even particular to Linux.

thanks for the advice

Offline gerald_clark

  • TinyCore Moderator
  • Hero Member
  • *****
  • Posts: 4254
Re: Boot Core with ntfs-3g extension
« Reply #37 on: October 30, 2013, 09:53:01 PM »
The third degree was to attempt to help you find something ready made you could use.
Good luck with your custom programming.

Offline casey

  • Newbie
  • *
  • Posts: 34
Re: Boot Core with ntfs-3g extension
« Reply #38 on: October 31, 2013, 06:46:30 AM »
@maro

can you help me for solve other problems?

thanks

Offline tinypoodle

  • Hero Member
  • *****
  • Posts: 3857
Re: Boot Core with ntfs-3g extension
« Reply #39 on: October 31, 2013, 07:45:02 AM »
Not sure what you refer to as "other problems", but the intended indiscriminate force mounting of filesystems at boot has a high potential to create serious problems in general, and more particularly so with ntfs in read-write mode.
"Software gets slower faster than hardware gets faster." Niklaus Wirth - A Plea for Lean Software (1995)

Offline casey

  • Newbie
  • *
  • Posts: 34
Re: Boot Core with ntfs-3g extension
« Reply #40 on: October 31, 2013, 08:16:36 AM »
no problem,
I ask only one command line prompt and with all the mounted drives,
I'll take that responsibility on the potential consequences to the file system,

15 years ago based my low-level software on DOS,
which gave me access to all drives and a command line,

DOS is now obsolete, does not read ntfs, does not support LBA48, does not support AHCI, reads only a few dozen mb of ram, does not support long file names,

for this I am trying to build me a replacement based on a linux operating system that is very good, in some respects the best

Offline Rich

  • Administrator
  • Hero Member
  • *****
  • Posts: 11632
Re: Boot Core with ntfs-3g extension
« Reply #41 on: October 31, 2013, 12:59:47 PM »
Hi casey
Read this thread:
http://forum.tinycorelinux.net/index.php/topic,12356.msg66630.html#msg66630
You will find knowing how to write a script (batch file) is a very useful skill to have when working under Linux.

Offline casey

  • Newbie
  • *
  • Posts: 34
Re: Boot Core with ntfs-3g extension
« Reply #42 on: October 31, 2013, 01:49:14 PM »
Hi casey
Read this thread:
http://forum.tinycorelinux.net/index.php/topic,12356.msg66630.html#msg66630
You will find knowing how to write a script (batch file) is a very useful skill to have when working under Linux.

thanks for reporting,
I will study the topic given to you, and I will try to create a working script,

can you help me to enter the ServerX in my Core-current.iso?
and let me know how to start it when I need it?

I need that in ServerX appear only the command line, without the bar style application Mac OS
« Last Edit: October 31, 2013, 01:55:52 PM by casey »