Tiny Core Base > TCB Q&A Forum
Is there a VNC server that supports file transfer function for tinycore?
worm:
--- Quote from: polikuo on November 29, 2024, 07:28:05 AM ---
--- Quote from: worm on November 29, 2024, 05:26:05 AM ---In the afternoon, I tested x11vnc on a 64 bit system and used the command line: (x11vnc -permitfiletransfer) to run VNC server normally, but the file transfer function is still not available!
--- End quote ---
--- Quote from: worm on November 29, 2024, 05:30:26 AM ---These extensions have been installed on the system. I tested 64 bit mainly using x11vnc, but the results were not satisfactory. It still does not support VNC file transfer function!
--- End quote ---
Checking the manual page
There are other options related with file-transfer, maybe they are related ?
--- Quote ----tightfilexfer
Enable the TightVNC file transfer extension.
--- End quote ---
Oh~, almost forgot, have you check the permission of the target directory ?
--- End quote ---
permission of the target directory? What does this mean? According to the current test results, under tinycore in X64, X11VNC is installed, and only commands such as [sudo x11vnc -forever -loop -ultrafilexfer], when combined with UltraVNC's vncviewer.exe, can achieve file transfer functionality! But it cannot be copied and pasted, only VNC-Viewer-7.13.0-Wdows-64bit.exe and TightVNC's tvnviewer.exe can achieve the copy and paste function! Other parameters such as [-permitfiletransfer -tightfilexfer] do not take effect!
polikuo:
By "target directory", I mean, the location where you are copying from or to.
Are you copying files from windows to /mnt/sda1 ?
Usually, the ownership of /mnt/sda1 is root:root, so you can't just copy into it.
--- Quote from: worm on November 29, 2024, 09:38:49 AM ---only commands such as [sudo x11vnc -forever -loop -ultrafilexfer], when combined with UltraVNC's vncviewer.exe, can achieve file transfer functionality
--- End quote ---
This means you CAN transfer files, right ?
--- Quote from: worm on November 29, 2024, 09:38:49 AM ---But it cannot be copied and pasted, only VNC-Viewer-7.13.0-Wdows-64bit.exe and TightVNC's tvnviewer.exe can achieve the copy and paste function!
--- End quote ---
Are you expecting that by dragging files from windows, it'll just pop up on TC desktop ?
If that's the case, that would be a total different issue.
You'll need a much heavier desktop environment.
worm:
--- Quote from: polikuo on November 29, 2024, 09:56:46 AM ---By "target directory", I mean, the location where you are copying from or to.
Are you copying files from windows to /mnt/sda1 ?
Usually, the ownership of /mnt/sda1 is root:root, so you can't just copy into it.
--- Quote from: worm on November 29, 2024, 09:38:49 AM ---only commands such as [sudo x11vnc -forever -loop -ultrafilexfer], when combined with UltraVNC's vncviewer.exe, can achieve file transfer functionality
--- End quote ---
This means you CAN transfer files, right ?
--- Quote from: worm on November 29, 2024, 09:38:49 AM ---But it cannot be copied and pasted, only VNC-Viewer-7.13.0-Wdows-64bit.exe and TightVNC's tvnviewer.exe can achieve the copy and paste function!
--- End quote ---
Are you expecting that by dragging files from windows, it'll just pop up on TC desktop ?
If that's the case, that would be a total different issue.
You'll need a much heavier desktop environment.
--- End quote ---
No, just copying and pasting the clipboard content! At present, testing shows that only X11VNC under X64 can achieve it, and there seems to be no VNC SERVER available on 32-bit.
GNUser:
Maybe a clipboard manager would help? It wouldn't hurt to try. Parcellite is in the TCL15 repo (both x86 and x86_64).
Navigation
[0] Message Index
[*] Previous page
Go to full version