General TC > Tiny Core Netbooks

TinyCore Install on a HP Laptop - GRUB - ISO boot

(1/2) > >>

RYTCL:
Setup :
   HP Pavilion x360 - 8GB RAM - SSD
   Boot Loader : GRUB - UEFI
   ISO : TinyCorePure64-11.1.iso
   
   /dev/sda1 : FAT32 : EFI System Partition
   /dev/sda8 : EXT4  : LABEL='ISO.Disk'  - TinyCore manual setup
   /dev/sda9 : EXT4  : LABEL='TinyCore'  - Reserved for TinyCore Install

   /dev/sdb  : FAT32 : USB Disk

GRUB.CFG
   #----------------------------------------------------
   menuentry 'INSTALL - TinyCore 11.1 - ISO Loopback' {
     set root=(hd0,gpt8)
     set isofile='/iso_files/TinyCorePure64-11.1.iso'
     
     echo '..... LoopBack TinyCore 11.1 .....'
     loopback loop $isofile

     echo '..... Loading TinyCore 11.1 VMLINUZ .....'
     linux (loop)/boot/vmlinuz64 waitusb=5 loglevel=5 cde showapps pause iso=/mnt/sda8/$isofile

     echo '..... Loading TinyCore 11.1 COREPURE64 .....'
     linux (loop)/boot/corepure64.gz

     echo '..... Booting TinyCore 11.1 .....'
   }
   #----------------------------------------------------


What works:

o  TinyCore 11.1 64 bit gets loaded.
o  GUI desktop is presented
o  Buttons present - Exit,  Editor, Control Panel, Apps, Run-Program, Mount-Tool, Terminal

Issues:
1) No TC-Install
2) No Wifi Install / Config
3) No Ethernet configuration options

* Need help to install TINYCORE on to a HD-Partition

Juanito:
TinyCorePure64 does not have tc-install or wifi included - you can load these extensions after boot.

Ethernet configuration options are found in cpanel.

RYTCL:
Wired Ethernet not working.

From dmesg log 

r8169 0000:04:00.0: Direct firmware load for rtl_nic/rtl8106e-1.fw failed with error -2
r8169 0000:04:00.0: Falling back to sysfs fallback for: rtl_nic/rtl8106e-1.fw
r8169 0000:04:00.0: Unable to load firmware rtl_nic/rtl8106e-1.fw (-11)


Is it possible to capture the boot  messages that show up into a log file.  I can capture 'dmesg' info into a file.  Boot messages that show up are more concise and may help in debugging.

Juanito:
Did you check the apps gui provides function to see if any extensions contain rtl8106e-1.fw?

Edit: the missing file is provided by the  firmware-rtl_nic extension.

RYTCL:
Ethernet is now working.  I changed boot option waitusb=15  and also plugged in the n/w cable before booting.   I still see the same error message in dmesg, but Internet connectivity is now working.

I installed tc-install-GUI.tgz extension and "tc-install" now shows up.

I tried running the install

Source: /mnt/cdrom/boot/corepure64.gz
Type : Frugal
Target :  sda9
Format : none
Install TCE/CD Directory : /mnt/cdrom/cde/

ERROR:  sda appears to have a partition already mounted.  Unmount it and run installer again


I cannot unmount sda8 as the ISO is mounted and runs from this partition.

Any suggestions...

Also,
1.  What extension to install for WIFI
2.  How to configure Synaptics Touchpad  to enable TAPPING - 1 for Left Mouse, 2 for Right Mouse

Navigation

[0] Message Index

[#] Next page