Kernel 4.19.10 and USB WiFi RTL8188EUS

[snake_air]

Hi
I  try to load a USB WiFi RTL8188EUS, with lsusb TC see it, i tried with more tcz file without success, i tried also load manually a 8188eu.ko , but im suer that wrong corret step, with iwconfig not see a card.
Can you help me ?

[Rich]

Hi snake_air
I suspect you need  firmware-rtlwifi.tcz  and  wireless-4.19.10-tinycore.tcz  if you haven't already installed them.

[Rich]

Hi snake_air
You'll also want  wifi.tcz.  Don't forget to read the  .info  file:
http://tinycorelinux.net/10.x/x86/tcz/wifi.tcz.info

[snake_air]

Hi RICH
I add a on my bootlist firmware-rtlwifi.tcz  and  wireless-4.19.10-tinycore.tcz, wifi.tcz already done, the net continue not start. 

[Rich]

Hi snake_air
Post the output of this command:

Code: [Select]

dmesg | grep -i rtl

[Rich]

Hi snake_air
And post the output of this command:

Code: [Select]

lsmod

[snake_air]

Hi Rich
below a info request:

Dmesg

Code: [Select]

r8169 0000:01:00.0 eth0: RTL8168b/8111b, 00:0b:ab:6c:83:f3, XID 38000000, IRQ 24
r8169 0000:02:00.0 eth1: RTL8168b/8111b, 00:0b:ab:6c:83:f4, XID 38000000, IRQ 25
RTL8211B Gigabit Ethernet r8169-100:00: attached PHY driver [RTL8211B Gigabit Ethernet] (mii_bus:phy_addr=r8169-100:00, irq=IGNORE)
RTL8211B Gigabit Ethernet r8169-200:00: attached PHY driver [RTL8211B Gigabit Ethernet] (mii_bus:phy_addr=r8169-200:00, irq=IGNORE)
LSUSB

Code: [Select]

Bus 001 Device 007: ID 0bda:8179 Realtek Semiconductor Corp. RTL8188EUS 802.11n Wireless Network Adapter
Bus 001 Device 008: ID 1a2c:0021 China Resource Semico Co., Ltd Keyboard
Bus 001 Device 006: ID 04f2:0909 Chicony Electronics Co., Ltd
Bus 001 Device 004: ID 1a40:0101 Terminus Technology Inc. Hub
Bus 001 Device 003: ID 1a40:0101 Terminus Technology Inc. Hub
Bus 001 Device 002: ID 23a9:ef18 
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    [EDIT]: Added code tags.  Rich

[Rich]

Hi snake_air
I don't see the 8188 showing up in dmesg. Unplug the adapter, count to 5, and plug it back in. Then post the output of:

Code: [Select]

dmesg | tail -n 30

[snake_air]

Hi Rich
below a DMESG

Code: [Select]

cfg80211: failed to load regulatory.db
usb 1-2.3: reset high-speed USB device number 9 using ehci-pci
mt7601u 1-2.3:1.0: ASIC revision: 76010001 MAC revision: 76010500
mt7601u 1-2.3:1.0: Direct firmware load for mt7601u.bin failed with error -2
mt7601u 1-2.3:1.0: Falling back to syfs fallback for: mt7601u.bin
mt7601u 1-2.3:1.0: Firmware Version: 0.1.00 Build: 7640 Build time: 201302052146____
mt7601u 1-2.3:1.0: EEPROM ver:0c fae:00
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
usbcore: registered new interface driver mt7601u
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
mt7601u 1-2.3:1.0: Error: RX urb failed:-71
usb 1-2.3: USB disconnect, device number 9
usb 1-2.4: USB disconnect, device number 7
usb 1-2.4: new high-speed USB device number 10 using ehci-pci
usb 1-2.4: USB disconnect, device number 10
usb 1-2.4: new high-speed USB device number 11 using ehci-pci
    [EDIT]: Added code tags.  Rich

[snake_air]

any news ?

[Juanito]

as per:

https://github.com/kuba-moo/mt7601u/issues/64

..post dated 2019/03/10, it looks like the driver needs patching?