Tiny Core Base > TCB Q&A Forum

Via Network Modules

(1/2) > >>

robc:
I haven't been able to get my NIC to connect to my network. The NIC is a Via VT6122 chip. I have used the via_velocity module, this creates the eth0 device and I can configure the port with ifconfig but I get the message:
--- Quote ---eth0: Link auto-negotiation speed 1000M bps full duplex
eth0: failed to detect cable link
--- End quote ---

I downloaded and compiled VIA's driver from VIA Arena but the results were the same.
According to this post: http://ubuntuforums.org/showthread.php?t=420432 the via_velocity module uses the crc_ccitt module. Is this module built into the kernel or was it removed? Is there something that I'm missing?

dmesg:
--- Quote ---e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
--- End quote ---

after loading via_velocity module:
--- Quote ---VIA Networking Velocity Family Gigabit Ethernet Adapter Driver Ver. 1.14
Copyright (c) 2002, 2003 VIA Networking Technologies, Inc.
Copyright (c) 2004 Red Hat Inc.
ACPI: PCI Interrupt 0000:02:05.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
eth0: VIA Networking Velocity Family Gigabit Ethernet Adapter
--- End quote ---

After loading velocityget module from VIA Arena:
--- Quote ---VIA Networking Velocity Family Gigabit Ethernet Adapter Driver Ver. 1.36
Copyright (c) 2002, 2003 VIA Networking Technologies, Inc.
eth0: VIA Networking Velocity Family Gigabit Ethernet Adapter
--- End quote ---

lspci -v:
--- Quote ---02:05.0   Ethernet controller: VIA Technologies, Inc. VT6120/VT6121/VT6122 Gigabit Ethernet Adapter (rev 11)
   Subsystem: VIA Technologies, Inc. Unkown device 0110
   Flags: 66MHz, medium devsel, IRQ 11
   I/O ports as dc00 [size=256]
   Memory at dfeff000 (32-bit, non-prefetchable) [size=256]
   Capabilities: <access denied>
   Kernel modules: via-velocity
--- End quote ---

robc:
I was able to get my NIC to work. I ended up compiling and installing ethtool (http://sourceforge.net/projects/gkernel/) and forced the NIC to communicate at 100baseT full duplex using the velocityget v1.36 module from VIA Arena.

I think this module should replace the via-velocity one since it is updated and actually supports the hardware it was designed for...though I may have to submit an ethtool package for those who don't have ipv6 equipment (including myself).

So now I'll put together this package for ethtool, unless anyone objects

^thehatsrule^:
What happens if you try to force the connection setting with the included kernel modules?

(Sounds like something is still going wrong if it can't auto-negotiate, though)

robc:
I tried to use ethtool and force the speed and duplex to 100 full with the included via-velocity module, but ethtool gave me this error:
--- Quote ---Cannot set new settings: Invalid argument
  not setting speed
--- End quote ---

I tried this again just now with the base norestore options and only loaded my ethtool-6 extension and got the same results when I used the native via-velocity module. I then rmmod via-velocity, installed my velocityget module extention, modprobe velocityget. After that the ethtool was able to set the parameters of the NIC and I was able to establish a connection with my network and be able to download extensions using the appbrowser.

I emailed these 2 extensions to the tcesubmit

curaga:
I think hats meant the module options, see "modinfo via-velocity"

Navigation

[0] Message Index

[#] Next page