c@box:~$ lsmod
Module Size Used by Not tainted
speedstep_lib 12288 0
cpufreq_conservative 12288 0
cpufreq_stats 12288 0
cpufreq_powersave 12288 0
cpufreq_userspace 12288 0
ppdev 12288 0
squashfs 24576 149
lz4_decompress 12288 1 squashfs
parport_pc 24576 0
floppy 45056 0
pcspkr 12288 0
8250_fintek 12288 0
parport 28672 2 ppdev,parport_pc
video 20480 0
backlight 12288 1 video
natsemi 20480 0
loop 16384 298
battery 16384 0
ac 12288 0
acpi_cpufreq 12288 0
tc@box:~$ tce-load -i carl9170-modules-KERNEL
carl9170-modules-4.2.9-tinycore.tcz: OK
tc@box:~$ lsmod
Module Size Used by Not tainted
carl9170 57344 0
mac80211 221184 1 carl9170
ath 16384 1 carl9170
cfg80211 135168 3 carl9170,mac80211,ath
speedstep_lib 12288 0
cpufreq_conservative 12288 0
cpufreq_stats 12288 0
cpufreq_powersave 12288 0
cpufreq_userspace 12288 0
ppdev 12288 0
squashfs 24576 150
lz4_decompress 12288 1 squashfs
parport_pc 24576 0
floppy 45056 0
pcspkr 12288 0
8250_fintek 12288 0
parport 28672 2 ppdev,parport_pc
video 20480 0
backlight 12288 1 video
natsemi 20480 0
loop 16384 300
battery 16384 0
ac 12288 0
acpi_cpufreq 12288 0
tc@box:~$ dmesg | tail -20
random: nonblocking pool is initialized
eth0: DSPCFG accepted after 0 usec.
eth0: link up.
eth0: Setting full-duplex based on negotiated link capability.
mtrr: no MTRR for d8000000,3ff0000 found
usb 1-2: reset full-speed USB device number 3 using ohci-pci
usb 1-2: Direct firmware load for carl9170-1.fw failed with error -2
usb 1-2: Falling back to user helper
usbcore: registered new interface driver carl9170
usb 1-2: driver API: 1.9.7 2012-12-15 [1-1]
usb 1-2: firmware API: 1.9.6 2012-07-07
ath: EEPROM regdomain: 0x809c
ath: EEPROM indicates we should expect a country code
ath: doing EEPROM country->regdmn map search
ath: country maps to regdmn code: 0x52
ath: Country alpha2 being used: CN
ath: Regpair used: 0x52
ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
input: phy0 WPS Button as /devices/pci0000:00/0000:00:02.0/usb1/1-2/1-2:1.0/ieee80211/phy0/input9
usb 1-2: Atheros AR9170 is registered as 'phy0'
tc@box:~$
wicd still doesn't work. This line is the cause?
usb 1-2: Direct firmware load for carl9170-1.fw failed with error -2