Tiny Core Base > CorePlus
WiFi Cannot Scan
Juanito:
--- Quote from: eltone on January 11, 2014, 03:58:08 PM ---WLAN BCM4318 has incorrect firmware!
eltone
--- End quote ---
b43/ucode5.fw is in the cut firmware, did you cut it/load it before you loaded the wireless-KERNEL extension (which would load the b43 module, which expects to find the firmware when it is loaded)?
Juanito:
--- Quote from: eltone on January 11, 2014, 11:06:42 PM ---Thread indicated b43-fwcutter.tcz is flawed.
--- End quote ---
I don't think so, but the firmware probably needs to be installed before the b43 module (contained in the wireless-KERNEL extension) is loaded.
eltone:
--- Quote from: Juanito on January 12, 2014, 01:18:47 AM ---
--- Quote from: eltone on January 11, 2014, 11:06:42 PM ---Thread indicated b43-fwcutter.tcz is flawed.
--- End quote ---
I don't think so, but the firmware probably needs to be installed before the b43 module (contained in the wireless-KERNEL extension) is loaded.
--- End quote ---
hi,
Please translate, so a digital analyzer is not required.
Everything is installed at the factory (original factory settings). The end-user's job is to cut/install firmware. No-wonder it fails.
eltone
Juanito:
check wireless is enabled in bios and any hardware wireless switch is set to "on"
reboot your machine without any firmware or wireless extensions loaded
cut and install the b43 firmware as detailed above
load the wireless-KERNEL extension
paste the results of "dmesg | tail -20" or similar
eltone:
--- Quote from: Juanito on January 12, 2014, 03:50:45 AM ---check wireless is enabled in bios and any hardware wireless switch is set to "on"
reboot your machine without any firmware or wireless extensions loaded
cut and install the b43 firmware as detailed above
load the wireless-KERNEL extension
paste the results of "dmesg | tail -20" or similar
--- End quote ---
hi,
paste data:
--- Code: ---tc@box:~$ dmesg | tail -20
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] Attached SCSI removable disk
usb 2-3.3: new full-speed USB device number 3 using ohci_hcd
input: ImPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input8
usb 2-3.4: new full-speed USB device number 4 using ohci_hcd
loop: module loaded
Adding 250072k swap on /dev/zram0. Priority:-1 extents:1 across:250072k SS
usb 4-1: new low-speed USB device number 2 using ohci_hcd
squashfs: version 4.0 (2009/01/31) Phillip Lougher
input: Kensington Kensington USB Wireless Mouse as /devices/pci0000:00/0000:00:14.4/0000:06:04.0/0000:07:00.0/usb4/4-1/4-1:1.0/input/input9
hid-generic 0003:047D:1039.0001: input,hidraw0: USB HID v1.00 Mouse [Kensington Kensington USB Wireless Mouse] on usb-0000:07:00.0-1/input0
Adding 1023996k swap on /dev/sdb2. Priority:-2 extents:1 across:1023996k
microcode: AMD CPU family 0xf not supported
8139too 0000:06:06.0 eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
microcode: AMD CPU family 0xf not supported
cfg80211: Calling CRDA to update world regulatory domain
b43-phy0: Broadcom 4318 WLAN found (core revision 9)
b43-phy0: Found PHY: Analog 3, Type 2 (G), Revision 7
Broadcom 43xx driver loaded [ Features: PMNL ]
ieee80211 phy0: Selected rate control algorithm 'pid'
tc@box:~$
--- End code ---
The balls in your court . . .
eltone
Navigation
[0] Message Index
[#] Next page
[*] Previous page
Go to full version