dCore Import Debian Packages to Mountable SCE extensions > Allwinner A10

A10 boot files

<< < (8/13) > >>

roberts:
I am not knowledgable on GPIO and SPI as these have more to do with the maker crowd and are not needed for desktop. 

You don't have any spi devices.
See: ls -l /dev/spi*

As far as your question about rebooting:
One step at a time. First be sure the module works then you can make a simple sce for them that will load upon boot.

persian:
Dear Roberts,

I configured the script.bin for GPIO and SPI .

GPIO module works fine but I must run insmod every time I reboot the Marsboard.

I don't know how to make a loadable sce for boot time.

Also the insmod of SPI module makes Segmentation fault error.

My SPI settings in script.bin are as follow:

[spi0_para]
spi_used = 1
spi_cs_bitmap = 1
spi_cs0 = port:PI10<3><default><default><default>
spi_sclk = port:PI11<3><default><default><default>
spi_mosi = port:PI12<3><default><default><default>
spi_miso = port:PI13<3><default><default><default>

[spi1_para]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PA00<4><default><default><default>
spi_sclk = port:PA01<4><default><default><default>
spi_mosi = port:PA02<4><default><default><default>
spi_miso = port:PA03<4><default><default><default>

[spi2_para]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PB14<2><default><default><default>
spi_sclk = port:PB15<2><default><default><default>
spi_mosi = port:PB16<2><default><default><default>
spi_miso = port:PB17<2><default><default><default>
spi_cs0 = port:PC19<3><default><default><default>
spi_sclk = port:PC20<3><default><default><default>
spi_mosi = port:PC21<3><default><default><default>
spi_miso = port:PC22<3><default><default><default>

[spi3_para]
spi_used = 0
spi_cs_bitmap = 1
spi_cs0 = port:PA05<3><default><default><default>
spi_sclk = port:PI06<3><default><default><default>
spi_mosi = port:PI07<3><default><default><default>
spi_miso = port:PI08<3><default><default><default>
spi_cs1 = port:PA09<3><default><default><default>

[spi_devices]
spi_dev_num = 1

[spi_board0]
modalias = "My SPI port-0"
max_speed_hz = 12000000
bus_num = 1
chip_select = 0
mode = 3
full_duplex = 0
manual_cs = 0

Thank you for your helps.

roberts:
There are many changes in this area with newer kernel. Should be worth investigating, e.g.
CONFIG_SPI_SPIDEV

persian:
Dear friends;

Hi,

Today my import did not work and it exit by no error!

When I traced the /usr/bin/import script file, I found that the first wget command with the following parameters return an error:

The line:
      wget -O /tmp/.depfile -cq "$IMPORTMIRROR"/PKGADDDEPS 2"
with the final content:
      wget -O /tmp/.depfile -cq http://repo.tinycorelinux.net/5.x/import/PKGADDDEPS 2

Returned message:
      wget: server returned error: HTTP/1.1 416 Requested Range Not Satisfiable

What's wrong ?

Also I need a command like lsusb but I don't find it.

Please help me about these problems.

Thank you.

roberts:
Make sure your /tmp directory is writable by user tc.

Navigation

[0] Message Index

[#] Next page

[*] Previous page