WelcomeWelcome | FAQFAQ | DownloadsDownloads | WikiWiki

Author Topic: OSS error with 4.2 (AMD K6-III)  (Read 2297 times)

Offline floppy

  • Hero Member
  • *****
  • Posts: 577
OSS error with 4.2 (AMD K6-III)
« on: January 08, 2012, 10:47:00 AM »
at the end of the dmesg:
...
     9.398180] Adding 98276k swap on /dev/sdc2.  Priority:-1 extents:1 across:98276k
[    9.554517] EXT4-fs (sda2): mounting ext3 file system using the ext4 subsystem
[    9.582353] EXT4-fs (sda2): warning: checktime reached, running e2fsck is recommended
[    9.582910] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[   24.820359] Linux agpgart interface v0.103
[   24.909256] agpgart: Detected VIA Apollo MVP3 chipset
[   24.994266] agpgart-via 0000:00:00.0: AGP aperture is 64M @ 0xd8000000
[   38.937597] osscore: This processor architecture is not compatible with vmix (info=-1) - Not enabled.
[   39.001642] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
[   39.001657] PCI: setting IRQ 5 as level-triggered
[   39.001680] oss_sbpci 0000:00:12.0: PCI INT A -> Link[LNKB] -> GSI 5 (level, low) -> IRQ 5
[   39.073432] usbcore: registered new interface driver oss_usb
[   40.982252] 8139too 0000:00:11.0: eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1
[   46.601864] [drm] Initialized drm 1.1.0 20060810
[   46.622076] pci 0000:01:00.0: PCI INT A -> Link[LNKA] -> GSI 11 (level, low) -> IRQ 11
[   46.626866] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[   46.626882] [drm] No driver support for vblank timestamp query.
[   46.626898] [drm] Initialized mga 3.2.1 20051102 for 0000:01:00.0 on minor 0
[   46.633822] agpgart-via 0000:00:00.0: AGP 1.0 bridge
[   46.633878] agpgart-via 0000:00:00.0: putting AGP V2 device into 2x mode
[   46.633944] pci 0000:01:00.0: putting AGP V2 device into 2x mode
[   50.004516] agpgart-via 0000:00:00.0: AGP 1.0 bridge
[   50.004569] agpgart-via 0000:00:00.0: putting AGP V2 device into 2x mode
[   50.004636] pci 0000:01:00.0: putting AGP V2 device into 2x mode
[ 1479.193400] process `skype' is using obsolete setsockopt SO_BSDCOMPAT

So, OSS is not adapted to my desktop? (I can hear).
Speaking with skype seems an issue "Problem with Audio Capture" in the skype test menu (skype-oss from this forum).
Setups in ossmix are here  http://imagebin.org/192474
No webcam is started (not enough power for it..).
« Last Edit: January 08, 2012, 11:10:40 AM by floppy »
AMD K6-IIIATZ 550MHz MB DFI K6xv3/+66
P4 HP DC7100 3GB 3GHz
Samsung NC10 boot from SD card port (via USB reader)
.. all TinyCore proofed

Offline curaga

  • Administrator
  • Hero Member
  • *****
  • Posts: 11022
Re: OSS error with 4.2 (AMD K6-III)
« Reply #1 on: January 08, 2012, 12:08:44 PM »
http://www.opensound.com/wiki/index.php/Building_OSSv4_from_source

The wiki says Geode cpus have the same. I assume vmix uses some 686 float instructions.
edit: Fixed-point would be lower quality, float is the default because of that.

Note that not having vmix doesn't mean no sound, it would mean only one app can use sound at a time.
The only barriers that can stop you are the ones you create yourself.

Offline floppy

  • Hero Member
  • *****
  • Posts: 577
Re: OSS error with 4.2 (AMD K6-III)
« Reply #2 on: January 08, 2012, 03:00:49 PM »
@curaga
how to test the capture function?
Command line?
Any gui tool?
AMD K6-IIIATZ 550MHz MB DFI K6xv3/+66
P4 HP DC7100 3GB 3GHz
Samsung NC10 boot from SD card port (via USB reader)
.. all TinyCore proofed

Offline curaga

  • Administrator
  • Hero Member
  • *****
  • Posts: 11022
Re: OSS error with 4.2 (AMD K6-III)
« Reply #3 on: January 09, 2012, 09:09:41 AM »
ossrecord, IIRC.
The only barriers that can stop you are the ones you create yourself.

Offline floppy

  • Hero Member
  • *****
  • Posts: 577
Re: OSS error with 4.2 (AMD K6-III)
« Reply #4 on: January 17, 2012, 03:45:38 PM »
Hello, I will have still to dig in using this ossrecord.
I made a quick check with skype (testcall). No sucess.
I can hear the testcall dialing.
The test call abort: it seems not to capture any sound.
Here is the screen copy: http://imagebin.org/194156
My OSS settings should be modified? How? (headset connected via 2 connectors into the pci128 card).
Any idea is welcome.
« Last Edit: January 17, 2012, 03:48:06 PM by floppy »
AMD K6-IIIATZ 550MHz MB DFI K6xv3/+66
P4 HP DC7100 3GB 3GHz
Samsung NC10 boot from SD card port (via USB reader)
.. all TinyCore proofed