WelcomeWelcome | FAQFAQ | DownloadsDownloads | WikiWiki

Author Topic: Mount emmc on chuwi:hibox-hero  (Read 5985 times)

Offline simon1

  • Newbie
  • *
  • Posts: 12
Mount emmc on chuwi:hibox-hero
« on: August 06, 2017, 08:59:37 PM »
Hello,
I am newbie, by the will of fate i need to install TyniCore(3.x) on device chuwi:hibox-hero.
Among other things, there is a memory on board of this device - emmc 64GB (memory is implemented in the form of 3 chips, biggest chip is Toshiba Thg8m5g9b0jbaie K87429 Japan 1530KAE).
There is also extended card slot - standard sd.
I create bootable flash drive according to this http://forum.tinycorelinux.net/index.php/topic,19364.0.html and everething seems ok, But (little hairy but around the corner).
After downloading from a flash drive, a can't see this emmc memory in /mnt/ and there are no similar devices with the name "mmc" in /dev/, rebuildfstab does't help.
blkid sees onle my bootable flash drive
dmesg | grep mmc
Quote
mmc0: SDHCI controller on ACPI [INT33BB:00] using ADMA
mmc0: queuing unknown CIS tuple 0x80 (2 bytes)
mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
mmc0: queuing unknown CIS tuple 0x80 (3 bytes)
mmc0: queuing unknown CIS tuple 0x80 (7 bytes)
mmc0: new ultra high speed DDR50 SDIO card at address 0001
lsmod
Quote
Module                  Size  Used by    Not tainted
cpufreq_userspace      12288  0
cpufreq_powersave      12288  0
cpufreq_conservative    12288  0
squashfs               28672  9
loop                   20480 18
mmc_block              28672  0
battery                16384  0
fjes                   24576  0
8250_dw                12288  0
ac                     12288  0
intel_vbtn             12288  0
sparse_keymap          12288  1 intel_vbtn
int3406_thermal        12288  0
video                  28672  1 int3406_thermal
lpc_ich                20480  0
backlight              12288  2 int3406_thermal,video
r8169                  53248  0
sdhci_acpi             12288  0
sdhci                  24576  1 sdhci_acpi
pcspkr                 12288  0
processor_thermal_device    12288  0
intel_soc_dts_iosf     12288  1 processor_thermal_device
mii                    12288  1 r8169
mmc_core               69632  3 mmc_block,sdhci_acpi,sdhci
int3403_thermal        12288  0
xhci_pci               12288  0
xhci_hcd               81920  1 xhci_pci
int3400_thermal        12288  0
acpi_thermal_rel       12288  1 int3400_thermal
iosf_mbi               12288  2 sdhci_acpi,intel_soc_dts_iosf
int340x_thermal_zone    12288  2 processor_thermal_device,int3403_thermal
mei_txe                16384  0
mei                    40960  1 mei_txe
Tried this solution http://wiki.laptop.org/go/Tiny_Core_Linux/eMMC. On command  sudo echo mmc0:0001 > /sys/bus/mmc/drivers/mmcblk/unbind, got error "premission denied".

Question is: how to properly mount such memory to install TinyCore(3.x) on it?

Offline gerald_clark

  • TinyCore Moderator
  • Hero Member
  • *****
  • Posts: 4254
Re: Mount emmc on chuwi:hibox-hero
« Reply #1 on: August 06, 2017, 09:17:51 PM »
Try a newer version.  It will have a more recent kernel.

Offline simon1

  • Newbie
  • *
  • Posts: 12
Re: Mount emmc on chuwi:hibox-hero
« Reply #2 on: August 06, 2017, 09:30:28 PM »
sorry, I incorrectly specified the number of the kernel, i dowloaded the lates version from http://tinycorelinux.net/downloads.html
it means not 3.x, but 8.x
uname -r
Quote
Linux box 4.8.17-tinycore64 x86_64 GNU/Linux


Offline polikuo

  • Hero Member
  • *****
  • Posts: 714
Re: Mount emmc on chuwi:hibox-hero
« Reply #3 on: August 06, 2017, 11:09:41 PM »
Welcome simon1.

Just some guesses, maybe it's the naming issue ?
Usually, SD card partitions are assigned as /dev/mmcblk0p1, /dev/mmcblk0p2 ... etc.

I'd like to see what you'll get with fetch_devices.
(It's a part of tc-install.tcz, by the way.)

Or the terminal output of
Code: [Select]
fdisk -l

Offline simon1

  • Newbie
  • *
  • Posts: 12
Re: Mount emmc on chuwi:hibox-hero
« Reply #4 on: August 06, 2017, 11:32:24 PM »
in "/dev/" there is no "*mmc*" devices.
fetch-devices
Quote
sda2   On a removable device.
sda   On a removable device.
sda1   On a removable device.
fdisk -l
Quote
Disk /dev/sda: 2051 MB, 2051013632 bytes
64 heads, 62 sectors/track, 1009 cylinders
Units = cylinders of 3968 * 512 = 2031616 bytes

   Device Boot      Start         End      Blocks  Id System
/dev/sda1               2         600     1188416  83 Linux
/dev/sda2   *         601        1009      811456  ef EFI (FAT-12/16/32)
« Last Edit: August 06, 2017, 11:38:30 PM by simon1 »

Offline polikuo

  • Hero Member
  • *****
  • Posts: 714
Re: Mount emmc on chuwi:hibox-hero
« Reply #5 on: August 06, 2017, 11:55:49 PM »
Your kernel doesn't setup emmc properly.
Maybe it's the driver issue.
I'm rather inexperienced in this part.
You'll have to wait for others to help.

As for your earlier question:
Tried this solution http://wiki.laptop.org/go/Tiny_Core_Linux/eMMC. On command  sudo echo mmc0:0001 > /sys/bus/mmc/drivers/mmcblk/unbind, got error "premission denied".

You can't redirect with sudo just by doing that.
You can:
Code: [Select]
# switch to root
sudo su
echo mmc0:0001 > /sys/bus/mmc/drivers/mmcblk/unbind
exit
# or run shell as root
sudo sh -c 'echo mmc0:0001 > /sys/bus/mmc/drivers/mmcblk/unbind'

Offline simon1

  • Newbie
  • *
  • Posts: 12
Re: Mount emmc on chuwi:hibox-hero
« Reply #6 on: August 07, 2017, 12:02:03 AM »
polikuo, thanks for the answer, let's wait...

Offline curaga

  • Administrator
  • Hero Member
  • *****
  • Posts: 10957
Re: Mount emmc on chuwi:hibox-hero
« Reply #7 on: August 07, 2017, 01:04:06 AM »
You need to find out how the mmc is connected, what driver does it use on Android or other distros.
The only barriers that can stop you are the ones you create yourself.

Offline simon1

  • Newbie
  • *
  • Posts: 12
Re: Mount emmc on chuwi:hibox-hero
« Reply #8 on: August 07, 2017, 02:09:50 AM »
here is what i findout,
if I understood correctly, emmc connected that way https://yadi.sk/i/V5yfxVHJ3Lme8c
on chuwi device preinstalled windows 10, that using driver Toshiba 064G93 (date 21.06.2006, version 10.0.14393)
on Android did't found yet...

Offline Juanito

  • Administrator
  • Hero Member
  • *****
  • Posts: 14516
Re: Mount emmc on chuwi:hibox-hero
« Reply #9 on: August 07, 2017, 05:34:56 AM »
maybe you need one of these drivers loaded:
Code: [Select]
# MMC/SD/SDIO Host Controller Drivers
#
CONFIG_MMC_SDHCI=m
CONFIG_MMC_SDHCI_PCI=m
CONFIG_MMC_RICOH_MMC=y
CONFIG_MMC_SDHCI_ACPI=m
CONFIG_MMC_SDHCI_PLTFM=m
CONFIG_MMC_WBSD=m
CONFIG_MMC_TIFM_SD=m
CONFIG_MMC_SDRICOH_CS=m
CONFIG_MMC_CB710=m
CONFIG_MMC_VIA_SDMMC=m
CONFIG_MMC_VUB300=m
CONFIG_MMC_USHC=m
CONFIG_MMC_USDHI6ROL0=m
CONFIG_MMC_REALTEK_USB=m
CONFIG_MMC_TOSHIBA_PCI=m
CONFIG_MMC_MTK=m
CONFIG_MEMSTICK=m

If you load the pci-utils and usbutils extensions, does "lspci" or "lsusb" give any details of your device?

..something like:
Code: [Select]
$ lspci
...
03:00.0 SD Host controller: O2 Micro, Inc. SD/MMC Card Reader Controller (rev 01)

$ lsmod | grep sd
sdhci_acpi             12288  0
iosf_mbi               12288  1 sdhci_acpi
sdhci_pci              20480  0
sdhci                  24576  2 sdhci_acpi,sdhci_pci
mmc_core               69632  3 sdhci_acpi,sdhci_pci,sdhci

The drivers are at /lib/modules/4.8.17-tinycore/kernel/drivers/mmc/host
« Last Edit: August 07, 2017, 05:48:36 AM by Juanito »

Offline simon1

  • Newbie
  • *
  • Posts: 12
Re: Mount emmc on chuwi:hibox-hero
« Reply #10 on: August 07, 2017, 07:43:19 PM »
uploaded pci-utils and usbutils, here is results
lspci
Code: [Select]
00:00.0 Class 0600: Device 8086:2280 (rev 36)
00:02.0 Class 0300: Device 8086:22b0 (rev 36)
00:0b.0 Class 1180: Device 8086:22dc (rev 36)
00:14.0 Class 0c03: Device 8086:22b5 (rev 36)
00:1a.0 Class 1080: Device 8086:2298 (rev 36)
00:1c.0 Class 0604: Device 8086:22c8 (rev 36)
00:1f.0 Class 0601: Device 8086:229c (rev 36)
01:00.0 Class 0200: Device 10ec:8168 (rev 0c)

just in case
lspci -v
Code: [Select]
00:00.0 Class 0600: Device 8086:2280 (rev 36)
Subsystem: Device 8086:7270
Flags: bus master, fast devsel, latency 0
Kernel driver in use: iosf_mbi_pci

00:02.0 Class 0300: Device 8086:22b0 (rev 36)
Subsystem: Device 8086:7270
Flags: bus master, fast devsel, latency 0, IRQ 255
Memory at 90000000 (64-bit, non-prefetchable) [size=16M]
Memory at 80000000 (64-bit, prefetchable) [size=256M]
I/O ports at f000 [size=64]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: [d0] Power Management version 2
Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [b0] Vendor Specific Information: Len=07 <?>

00:0b.0 Class 1180: Device 8086:22dc (rev 36)
Subsystem: Device 8086:7270
Flags: fast devsel, IRQ 116
Memory at 9153b000 (64-bit, non-prefetchable) [size=4K]
Capabilities: [40] MSI: Enable+ Count=1/1 Maskable- 64bit-
Capabilities: [50] Power Management version 3
Kernel driver in use: proc_thermal

00:14.0 Class 0c03: Device 8086:22b5 (rev 36) (prog-if 30)
Subsystem: Device 8086:7270
Flags: bus master, medium devsel, latency 0, IRQ 119
Memory at 91500000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [70] Power Management version 2
Capabilities: [80] MSI: Enable+ Count=1/8 Maskable- 64bit+
Kernel driver in use: xhci_hcd

00:1a.0 Class 1080: Device 8086:2298 (rev 36)
Subsystem: Device 8086:7270
Flags: bus master, fast devsel, latency 0, IRQ 117
Memory at 91300000 (32-bit, non-prefetchable) [size=1M]
Memory at 91200000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [80] Power Management version 3
Capabilities: [a0] MSI: Enable+ Count=1/1 Maskable- 64bit-
Kernel driver in use: mei_txe

00:1c.0 Class 0604: Device 8086:22c8 (rev 36)
Flags: bus master, fast devsel, latency 0, IRQ 115
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff [size=4K]
Memory behind bridge: 91400000-914fffff [size=1M]
Prefetchable memory behind bridge: None
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] MSI: Enable+ Count=1/1 Maskable- 64bit-
Capabilities: [90] Subsystem: Device 8086:7270
Capabilities: [a0] Power Management version 3
Capabilities: [100] #00
Capabilities: [200] L1 PM Substates
Kernel driver in use: pcieport

00:1f.0 Class 0601: Device 8086:229c (rev 36)
Subsystem: Device 8086:7270
Flags: bus master, medium devsel, latency 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
Kernel driver in use: lpc_ich

01:00.0 Class 0200: Device 10ec:8168 (rev 0c)
Subsystem: Device 10ec:0123
Flags: bus master, fast devsel, latency 0, IRQ 118
I/O ports at e000 [size=256]
Memory at 91404000 (64-bit, non-prefetchable) [size=4K]
Memory at 91400000 (64-bit, prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 01
Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
Capabilities: [d0] Vital Product Data
Capabilities: [100] Advanced Error Reporting
Capabilities: [140] Virtual Channel
Capabilities: [160] Device Serial Number 01-00-00-00-68-4c-e0-00
Capabilities: [170] Latency Tolerance Reporting
Kernel driver in use: r8169

lsusb -v
Code: [Select]
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               3.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         3
  bMaxPacketSize0         9
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0003 3.0 root hub
  bcdDevice            4.08
  iManufacturer           3 Linux 4.8.17-tinycore64 xhci-hcd
  iProduct                2 xHCI Host Controller
  iSerial                 1 0000:00:14.0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           31
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
        bMaxBurst               0
Hub Descriptor:
  bLength              12
  bDescriptorType      42
  nNbrPorts             6
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  bHubDecLat          0.0 micro seconds
  wHubDelay             0 nano seconds
  DeviceRemovable    0x00
 Hub Port Status:
   Port 1: 0000.02a0 5Gbps power Rx.Detect
   Port 2: 0000.02a0 5Gbps power Rx.Detect
   Port 3: 0000.02a0 5Gbps power Rx.Detect
   Port 4: 0000.02a0 5Gbps power Rx.Detect
   Port 5: 0000.02a0 5Gbps power Rx.Detect
   Port 6: 0000.02a0 5Gbps power Rx.Detect
Binary Object Store Descriptor:
  bLength                 5
  bDescriptorType        15
  wTotalLength           15
  bNumDeviceCaps          1
  SuperSpeed USB Device Capability:
    bLength                10
    bDescriptorType        16
    bDevCapabilityType      3
    bmAttributes         0x02
      Latency Tolerance Messages (LTM) Supported
    wSpeedsSupported   0x0008
      Device can operate at SuperSpeed (5Gbps)
    bFunctionalitySupport   3
      Lowest fully-functional device speed is SuperSpeed (5Gbps)
    bU1DevExitLat          10 micro seconds
    bU2DevExitLat         512 micro seconds
Device Status:     0x0001
  Self Powered

Bus 001 Device 004: ID 0c40:8000 
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x0c40
  idProduct          0x8000
  bcdDevice            0.01
  iManufacturer           1 ELMCU
  iProduct                2 iPazzPort
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           59
    bNumInterfaces          2
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      1 Boot Interface Subclass
      bInterfaceProtocol      1 Keyboard
      iInterface              0
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.11
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      77
         Report Descriptors:
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval              10
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      1 Boot Interface Subclass
      bInterfaceProtocol      2 Mouse
      iInterface              0
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.11
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength     104
         Report Descriptors:
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0007  1x 7 bytes
        bInterval              10
Device Status:     0x0000
  (Bus Powered)

Bus 001 Device 003: ID 1c4f:0026 SiGma Micro Keyboard
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0         8
  idVendor           0x1c4f SiGma Micro
  idProduct          0x0026 Keyboard
  bcdDevice            1.10
  iManufacturer           1 SIGMACHIP
  iProduct                2 USB Keyboard
  iSerial                 0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           59
    bNumInterfaces          2
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xa0
      (Bus Powered)
      Remote Wakeup
    MaxPower               98mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      1 Boot Interface Subclass
      bInterfaceProtocol      1 Keyboard
      iInterface              0
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.10
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      54
         Report Descriptors:
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0008  1x 8 bytes
        bInterval              10
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         3 Human Interface Device
      bInterfaceSubClass      0 No Subclass
      bInterfaceProtocol      0 None
      iInterface              0
        HID Device Descriptor:
          bLength                 9
          bDescriptorType        33
          bcdHID               1.10
          bCountryCode            0 Not supported
          bNumDescriptors         1
          bDescriptorType        34 Report
          wDescriptorLength      50
         Report Descriptors:
           ** UNAVAILABLE **
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0003  1x 3 bytes
        bInterval              10
Device Status:     0x0000
  (Bus Powered)

Bus 001 Device 002: ID 058f:6387 Alcor Micro Corp. Flash Drive
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x058f Alcor Micro Corp.
  idProduct          0x6387 Flash Drive
  bcdDevice            1.41
  iManufacturer           1 JetFlash
  iProduct                2 Mass Storage Device
  iSerial                 3 SKQ0J7VG
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk-Only
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x01  EP 1 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x82  EP 2 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0200  1x 512 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0000
  (Bus Powered)

Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         1 Single TT
  bMaxPacketSize0        64
  idVendor           0x1d6b Linux Foundation
  idProduct          0x0002 2.0 root hub
  bcdDevice            4.08
  iManufacturer           3 Linux 4.8.17-tinycore64 xhci-hcd
  iProduct                2 xHCI Host Controller
  iSerial                 1 0000:00:14.0
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed (or root) hub
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0004  1x 4 bytes
        bInterval              12
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             7
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
    TT think time 8 FS bits
  bPwrOn2PwrGood       10 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0100 power
   Port 2: 0000.0503 highspeed power enable connect
   Port 3: 0000.0303 lowspeed power enable connect
   Port 4: 0000.0303 lowspeed power enable connect
   Port 5: 0000.0100 power
   Port 6: 0000.0100 power
   Port 7: 0000.0100 power
Device Status:     0x0001
  Self Powered

lsmod | grep sd
Code: [Select]
sdhci_acpi             12288  0
sdhci                  24576  1 sdhci_acpi
mmc_core               69632  2 sdhci_acpi,sdhci
iosf_mbi               12288  2 sdhci_acpi,intel_soc_dts_iosf

Offline Juanito

  • Administrator
  • Hero Member
  • *****
  • Posts: 14516
Re: Mount emmc on chuwi:hibox-hero
« Reply #11 on: August 08, 2017, 02:21:02 AM »
Oops, it shouldn't look like this:
Code: [Select]
$ lspci
...
03:00.0 Class 0805: Device 1217:8520 (rev 01)

..but should look like this:
Code: [Select]
$ lspci
...
03:00.0 SD Host controller: O2 Micro, Inc. SD/MMC Card Reader Controller (rev 01)

I corrected the pci-utils extension, could you update your copy and try again?

Offline simon1

  • Newbie
  • *
  • Posts: 12
Re: Mount emmc on chuwi:hibox-hero
« Reply #12 on: August 08, 2017, 03:15:19 AM »
done
lspci
Code: [Select]
00:00.0 Host bridge: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series SoC Transaction Register (rev 36)
00:02.0 VGA compatible controller: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCI Configuration Registers (rev 36)
00:0b.0 Signal processing controller: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series Power Management Controller (rev 36)
00:14.0 USB controller: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series USB xHCI Controller (rev 36)
00:16.0 USB controller: Intel Corporation Device 22b7 (rev 36)
00:1a.0 Encryption controller: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series Trusted Execution Engine (rev 36)
00:1c.0 PCI bridge: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCI Express Port #1 (rev 36)
00:1f.0 ISA bridge: Intel Corporation Atom/Celeron/Pentium Processor x5-E8000/J3xxx/N3xxx Series PCU (rev 36)
01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 0c)

but looks like my sd/mmc devices gone somewhere...

Offline Juanito

  • Administrator
  • Hero Member
  • *****
  • Posts: 14516
Re: Mount emmc on chuwi:hibox-hero
« Reply #13 on: August 08, 2017, 03:39:04 AM »
I guess it is not a pci device...

Could you try the following:
Code: [Select]
$ tce-load -i usbutils
$ sudo update-usbids.sh
$ lsusb
..just to double-check it is not a usb device either

Offline Juanito

  • Administrator
  • Hero Member
  • *****
  • Posts: 14516
Re: Mount emmc on chuwi:hibox-hero
« Reply #14 on: August 08, 2017, 03:48:18 AM »
you could also try this (since windows uses a toshiba driver):
Code: [Select]
$ sudo modprobe toshsd..and examine dmesg to see if anything relevant is reported when you try to load the driver