WelcomeWelcome | FAQFAQ | DownloadsDownloads | WikiWiki

Author Topic: piCore-7.1beta2 released  (Read 2389 times)

Online bmarkus

  • Administrator
  • Hero Member
  • *****
  • Posts: 6908
    • My Community Forum
piCore-7.1beta2 released
« on: March 13, 2016, 04:51:52 AM »
piCore-7.1beta2 released. Changes:

- kernel updated to 4.1.19
. micropython updated
. mc updated to 4.8.16
- openssh updated to 7.2p1

Download:

http://www.tinycorelinux.net/7.x/armv6/test_releases/
Béla
Ham Radio callsign: HA5DI

"Amateur Radio: The First Technology-Based Social Network."

Offline jncl

  • WikiUser
  • *
  • Posts: 38
Re: piCore-7.1beta2 released
« Reply #1 on: March 16, 2016, 03:00:57 PM »
Hi Béla

  I have tried this latest image on the following RPi's: A, B, B+, 2B, Zero. It loads on all but the Zero, which hangs with the splash screen displayed.

  I have attached the contents of the 'dmesg' command for each different type of RPi, that loaded, as you can see all but the RPi2B file have varying numbers of
Code: [Select]
uio: disagrees about version of symbol module_layout messages.

  HTH.

    Jon

Online bmarkus

  • Administrator
  • Hero Member
  • *****
  • Posts: 6908
    • My Community Forum
Re: piCore-7.1beta2 released
« Reply #2 on: March 16, 2016, 11:39:25 PM »
Jon

thanks for testing. It is my RPi2 dmesg:

Code: [Select]
root@box:/home/tc# dmesg
[    0.000000] Booting Linux on physical CPU 0xf00
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Initializing cgroup subsys cpuacct
[    0.000000] Linux version 4.1.19-piCore_v7+ (root@beta.hasix.org) (gcc version 4.9.1 (crosstool-NG 1.20.0) ) #1 SMP PREEMPT Wed Mar 9 16:22:48 CET 2016
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine model: Raspberry Pi 2 Model B Rev 1.1
[    0.000000] cma: Reserved 8 MiB at 0x3a000000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 241664
[    0.000000] free_area_init_node: node 0, pgdat 80889880, node_mem_map b97b4000
[    0.000000]   Normal zone: 2124 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 241664 pages, LIFO batch:31
[    0.000000] [bcm2709_smp_init_cpus] enter (9420->f3003010)
[    0.000000] [bcm2709_smp_init_cpus] ncores=4
[    0.000000] PERCPU: Embedded 13 pages/cpu @bab7c000 s20672 r8192 d24384 u53248
[    0.000000] pcpu-alloc: s20672 r8192 d24384 u53248 alloc=13*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 239540
[    0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2709.boardrev=0xa01041 bcm2709.serial=0x8e976f0e smsc95xx.macaddr=B8:27:EB:97:6F:0E bcm2708_fb.fbswap=1 bcm2709.uart_clock=3000000 bcm2709.disk_led_gpio=47 bcm2709.disk_led_active_low=0 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/ram0 elevator=deadline rootwait quiet nortc loglevel=3 noembed
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 935036K/966656K available (6118K kernel code, 536K rwdata, 1668K rodata, 420K init, 758K bss, 23428K reserved, 8192K cma-reserved)
[    0.000000] Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
    vmalloc : 0xbb800000 - 0xff000000   (1080 MB)
    lowmem  : 0x80000000 - 0xbb000000   ( 944 MB)
    modules : 0x7f000000 - 0x80000000   (  16 MB)
      .text : 0x80008000 - 0x807a2ba4   (7787 kB)
      .init : 0x807a3000 - 0x8080c000   ( 420 kB)
      .data : 0x8080c000 - 0x808923dc   ( 537 kB)
       .bss : 0x80895000 - 0x8095291c   ( 759 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000] NR_IRQS:608
[    0.000000] Architected cp15 timer(s) running at 19.20MHz (phys).
[    0.000000] clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000010] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000032] Switching to timer-based delay loop, resolution 52ns
[    0.000325] Console: colour dummy device 80x30
[    0.000562] console [tty1] enabled
[    0.000599] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.000626] pid_max: default: 32768 minimum: 301
[    0.000986] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.001008] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.002283] Initializing cgroup subsys blkio
[    0.002322] Initializing cgroup subsys memory
[    0.002356] Initializing cgroup subsys devices
[    0.002383] Initializing cgroup subsys freezer
[    0.002422] Initializing cgroup subsys net_cls
[    0.002496] CPU: Testing write buffer coherency: ok
[    0.002576] ftrace: allocating 20577 entries in 61 pages
[    0.053002] CPU0: update cpu_capacity 1024
[    0.053044] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
[    0.053061] [bcm2709_smp_prepare_cpus] enter
[    0.053196] Setting up static identity map for 0x8240 - 0x8274
[    0.112854] [bcm2709_boot_secondary] cpu:1 started (0) 17
[    0.113287] [bcm2709_secondary_init] enter cpu:1
[    0.113344] CPU1: update cpu_capacity 1024
[    0.113353] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
[    0.132842] [bcm2709_boot_secondary] cpu:2 started (0) 18
[    0.133197] [bcm2709_secondary_init] enter cpu:2
[    0.133232] CPU2: update cpu_capacity 1024
[    0.133241] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
[    0.152884] [bcm2709_boot_secondary] cpu:3 started (0) 17
[    0.153138] [bcm2709_secondary_init] enter cpu:3
[    0.153169] CPU3: update cpu_capacity 1024
[    0.153177] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
[    0.153274] Brought up 4 CPUs
[    0.153305] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[    0.153316] CPU: All CPU(s) started in HYP mode.
[    0.153325] CPU: Virtualization extensions available.
[    0.154290] devtmpfs: initialized
[    0.179152] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.179459] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.180583] pinctrl core: initialized pinctrl subsystem
[    0.181379] NET: Registered protocol family 16
[    0.187174] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[    0.188387] bcm2709.uart_clock = 3000000
[    0.194728] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.194746] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.194936] Serial: AMBA PL011 UART driver
[    0.195134] 3f201000.uart: ttyAMA0 at MMIO 0x3f201000 (irq = 83, base_baud = 0) is a PL011 rev2
[    0.195567] console [ttyAMA0] enabled
[    0.196133] bcm2835-mbox 3f00b880.mailbox: mailbox enabled
[    0.274483] bcm2708-dmaengine 3f007000.dma: DMA legacy API manager at f3007000, dmachans=0xf35
[    0.274530] bcm2708-dmaengine 3f007000.dma: Initialized 7 DMA channels (+ 1 legacy)
[    0.275266] bcm2708-dmaengine 3f007000.dma: Load BCM2835 DMA engine driver
[    0.275285] bcm2708-dmaengine 3f007000.dma: dma_debug:0
[    0.276071] SCSI subsystem initialized
[    0.276320] usbcore: registered new interface driver usbfs
[    0.276443] usbcore: registered new interface driver hub
[    0.276602] usbcore: registered new device driver usb
[    0.277340] raspberrypi-firmware soc:firmware: Attached to firmware from 2016-03-07 17:08
[    0.304720] Switched to clocksource arch_sys_counter
[    0.356784] FS-Cache: Loaded
[    0.357182] CacheFiles: Loaded
[    0.370587] NET: Registered protocol family 2
[    0.371966] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.372123] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.372330] TCP: Hash tables configured (established 8192 bind 8192)
[    0.372456] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.372521] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.372878] NET: Registered protocol family 1
[    0.373398] RPC: Registered named UNIX socket transport module.
[    0.373416] RPC: Registered udp transport module.
[    0.373427] RPC: Registered tcp transport module.
[    0.373438] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.373790] Trying to unpack rootfs image as initramfs...
[    0.822418] Freeing initrd memory: 4292K (babbf000 - baff0000)
[    0.835704] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.837188] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.852857] zpool: loaded
[    0.853385] VFS: Disk quotas dquot_6.6.0
[    0.853767] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.856269] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.856882] FS-Cache: Netfs 'nfs' registered for caching
[    0.858109] NFS: Registering the id_resolver key type
[    0.858193] Key type id_resolver registered
[    0.858207] Key type id_legacy registered
[    0.861582] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.861781] io scheduler noop registered
[    0.861805] io scheduler deadline registered (default)
[    0.862153] io scheduler cfq registered
[    0.865270] BCM2708FB: allocated DMA memory fa400000
[    0.865319] BCM2708FB: allocated DMA channel 0 @ f3007000
[    0.870984] Console: switching to colour frame buffer device 82x26
[    0.874564] Serial: 8250/16550 driver, 0 ports, IRQ sharing disabled
[    0.875991] vc-cma: Videocore CMA driver
[    0.876008] vc-cma: vc_cma_base      = 0x00000000
[    0.876020] vc-cma: vc_cma_size      = 0x00000000 (0 MiB)
[    0.876031] vc-cma: vc_cma_initial   = 0x00000000 (0 MiB)
[    0.876284] vc-mem: phys_addr:0x00000000 mem_base=0x3dc00000 mem_size:0x3f000000(1008 MiB)
[    0.892518] brd: module loaded
[    0.901602] loop: module loaded
[    0.902510] zram: Created 1 device(s)
[    0.903570] vchiq: vchiq_init_state: slot_zero = 0xba480000, is_master = 0
[    0.905397] Loading iSCSI transport class v2.0-870.
[    0.906339] usbcore: registered new interface driver smsc95xx
[    0.906422] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.106827] Core Release: 2.80a
[    1.106849] Setting default values for core params
[    1.106899] Finished setting default values for core params
[    1.307312] Using Buffer DMA mode
[    1.307327] Periodic Transfer Interrupt Enhancement - disabled
[    1.307338] Multiprocessor Interrupt Enhancement - disabled
[    1.307350] OTG VER PARAM: 0, OTG VER FLAG: 0
[    1.307367] Dedicated Tx FIFOs mode
[    1.307740] WARN::dwc_otg_hcd_init:1047: FIQ DMA bounce buffers: virt = 0xba414000 dma = 0xfa414000 len=9024
[    1.307779] FIQ FSM acceleration enabled for :
Non-periodic Split Transactions
Periodic Split Transactions
High-Speed Isochronous Endpoints
[    1.307804] dwc_otg: Microframe scheduler enabled
[    1.307875] WARN::hcd_init_fiq:412: FIQ on core 1 at 0x80424ce0
[    1.307895] WARN::hcd_init_fiq:413: FIQ ASM at 0x80425058 length 36
[    1.307915] WARN::hcd_init_fiq:438: MPHI regs_base at 0xbb8a8000
[    1.307966] dwc_otg 3f980000.usb: DWC OTG Controller
[    1.308019] dwc_otg 3f980000.usb: new USB bus registered, assigned bus number 1
[    1.308066] dwc_otg 3f980000.usb: irq 32, io mem 0x00000000
[    1.308121] Init: Port Power? op_state=1
[    1.308132] Init: Power Port (0)
[    1.308461] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.308482] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.308499] usb usb1: Product: DWC OTG Controller
[    1.308516] usb usb1: Manufacturer: Linux 4.1.19-piCore_v7+ dwc_otg_hcd
[    1.308532] usb usb1: SerialNumber: 3f980000.usb
[    1.309449] hub 1-0:1.0: USB hub found
[    1.309519] hub 1-0:1.0: 1 port detected
[    1.310041] dwc_otg: FIQ enabled
[    1.310055] dwc_otg: NAK holdoff enabled
[    1.310066] dwc_otg: FIQ split-transaction FSM enabled
[    1.310107] Module dwc_common_port init
[    1.310472] usbcore: registered new interface driver usb-storage
[    1.310755] mousedev: PS/2 mouse device common for all mice
[    1.311697] bcm2835-cpufreq: min=600000 max=900000
[    1.314297] sdhci: Secure Digital Host Controller Interface driver
[    1.314306] sdhci: Copyright(c) Pierre Ossman
[    1.314558] sdhost: log_buf @ ba413000 (fa413000)
[    1.414808] mmc0: sdhost-bcm2835 loaded - DMA enabled (>1)
[    1.415016] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.415429] ledtrig-cpu: registered to indicate activity on CPUs
[    1.415589] hidraw: raw HID events driver (C) Jiri Kosina
[    1.415772] usbcore: registered new interface driver usbhid
[    1.415780] usbhid: USB HID core driver
[    1.416109] Initializing XFRM netlink socket
[    1.416154] NET: Registered protocol family 17
[    1.416315] Key type dns_resolver registered
[    1.416663] Registering SWP/SWPB emulation handler
[    1.417367] registered taskstats version 1
[    1.448025] Key type encrypted registered
[    1.448139] vc-sm: Videocore shared memory driver
[    1.448154] [vc_sm_connected_init]: start
[    1.448740] [vc_sm_connected_init]: end - returning 0
[    1.450153] Freeing unused kernel memory: 420K (807a3000 - 8080c000)
[    1.492947] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.495961] mmc0: new high speed SDHC card at address e624
[    1.496476] mmcblk0: mmc0:e624 SL08G 7.40 GiB
[    1.497694]  mmcblk0: p1 p2 p3
[    1.504876] Indeed it is in host mode hprt0 = 00021501
[    1.684832] usb 1-1: new high-speed USB device number 2 using dwc_otg
[    1.685160] Indeed it is in host mode hprt0 = 00001101
[    1.885164] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[    1.885190] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    1.885880] hub 1-1:1.0: USB hub found
[    1.886000] hub 1-1:1.0: 5 ports detected
[    2.168863] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[    2.265771] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[    2.265816] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.269667] smsc95xx v1.0.4
[    2.302300] zram0: detected capacity change from 0 to 234434560
[    2.312672] random: mkswap urandom read with 60 bits of entropy available
[    2.324266] Adding 228936k swap on /dev/zram0.  Priority:-1 extents:1 across:228936k SSFS
[    2.333628] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-3f980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:97:6f:0e
[    2.424908] usb 1-1.3: new low-speed USB device number 4 using dwc_otg
[    2.531560] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c019
[    2.531612] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.531633] usb 1-1.3: Product: USB Optical Mouse
[    2.531650] usb 1-1.3: Manufacturer: Logitech
[    2.545825] input: Logitech USB Optical Mouse as /devices/platform/soc/3f980000.usb/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C019.0001/input/input0
[    2.547063] hid-generic 0003:046D:C019.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-3f980000.usb-1.3/input0
[    2.624993] usb 1-1.4: new high-speed USB device number 5 using dwc_otg
[    2.728196] usb 1-1.4: New USB device found, idVendor=0951, idProduct=1607
[    2.728266] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.728298] usb 1-1.4: Product: DataTraveler 2.0
[    2.728327] usb 1-1.4: Manufacturer: Kingston
[    2.728365] usb 1-1.4: SerialNumber: 2008012500000000000001E5
[    2.730423] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[    2.731478] scsi host0: usb-storage 1-1.4:1.0
[    3.041816] bcm2835-rng 3f104000.rng: hwrng registered
[    3.044653] gpiomem-bcm2835 3f200000.gpiomem: Initialised: Registers at 0x3f200000
[    3.045526] bcm2708_i2c 3f205000.i2c: BSC0 Controller at 0x3f205000 (irq 79) (baudrate 100000)
[    3.046117] bcm2708_i2c 3f804000.i2c: BSC1 Controller at 0x3f804000 (irq 79) (baudrate 100000)
[    3.049383] spi spi0.0: setting up native-CS0 as GPIO 8
[    3.050080] spi spi0.1: setting up native-CS1 as GPIO 7
[    3.276170] Adding 1435644k swap on /dev/mmcblk0p3.  Priority:-2 extents:1 across:1435644k SSFS
[    3.550700] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    3.672392] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[    3.725852] scsi 0:0:0:0: Direct-Access     Kingston DataTraveler 2.0 1.00 PQ: 0 ANSI: 2
[    3.729638] sd 0:0:0:0: [sda] 7888896 512-byte logical blocks: (4.04 GB/3.76 GiB)
[    3.730196] sd 0:0:0:0: [sda] Write Protect is off
[    3.730224] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[    3.730769] sd 0:0:0:0: [sda] No Caching mode page found
[    3.730799] sd 0:0:0:0: [sda] Assuming drive cache: write through
[    3.857174]  sda: sda1
[    3.865282] sd 0:0:0:0: [sda] Attached SCSI removable disk
[    7.942041] random: nonblocking pool is initialized
[   46.911251] uart-pl011 3f201000.uart: no DMA platform data
[   46.911679] i2c /dev entries driver
[   47.017170] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[   48.565641] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1

and lsmod:

Code: [Select]
root@box:/home/tc# lsmod
Module                  Size  Used by    Not tainted
i2c_dev                 6020  0
snd_soc_bcm2708_i2s     6728  0
snd_soc_core          133519  1 snd_soc_bcm2708_i2s
snd_pcm_dmaengine       3303  1 snd_soc_core
snd_pcm                75313  2 snd_soc_core,snd_pcm_dmaengine
snd_timer              18790  1 snd_pcm
snd_compress            7777  1 snd_soc_core
snd                    52662  4 snd_soc_core,snd_pcm,snd_timer,snd_compress
regmap_mmio             2969  1 snd_soc_bcm2708_i2s
evdev                  10230  1
spi_bcm2835             7252  0
i2c_bcm2708             5002  0
bcm2835_gpiomem         3023  0
bcm2835_rng             1816  0
uio_pdrv_genirq         2966  0
uio                     8340  1 uio_pdrv_genirq

Béla
« Last Edit: March 16, 2016, 11:44:14 PM by bmarkus »
Béla
Ham Radio callsign: HA5DI

"Amateur Radio: The First Technology-Based Social Network."

Offline Gerrelt

  • Full Member
  • ***
  • Posts: 176
Re: piCore-7.1beta2 released
« Reply #3 on: March 18, 2016, 12:06:25 PM »
Hi Béla,

   I'm testing this version on a Raspberry model B, but my WiFi adapter doesn't seem to work on this version.
It is this adapter:
Code: [Select]
tc@4-Gooseberry-PortableStereo:~$ lsusb | grep 7601
Bus 001 Device 007: ID 148f:7601 Ralink Technology, Corp. MT7601U Wireless Adapter

I've installed these extensions:
Code: [Select]
tce-load -wi firmware-ralinkwifi.tcz
tce-load -wi firmware-rtlwifi.tcz

It worked fine on piCore-7.0, and I do see the drivers are there:
Code: [Select]
tc@4-Gooseberry-PortableStereo:~$ sudo find / -name mt7601*
/usr/local/lib/modules/4.1.19-piCore+/kernel/drivers/net/wireless/mediatek/mt7601u
/usr/local/lib/modules/4.1.19-piCore+/kernel/drivers/net/wireless/mediatek/mt7601u/mt7601u.ko.gz
/lib/firmware/mt7601u.bin
/tmp/tcloop/wireless-4.1.19-piCore+/usr/local/lib/modules/4.1.19-piCore+/kernel/drivers/net/wireless/mediatek/mt7601u
/tmp/tcloop/wireless-4.1.19-piCore+/usr/local/lib/modules/4.1.19-piCore+/kernel/drivers/net/wireless/mediatek/mt7601u/mt7601u.ko.gz
/tmp/tcloop/firmware-ralinkwifi/lib/firmware/mt7601u.bin


But it's not loaded:
Code: [Select]
tc@4-Gooseberry-PortableStereo:~$ lsmod
Module                  Size  Used by    Not tainted
snd_usb_audio         139140  0
snd_usbmidi_lib        22679  1 snd_usb_audio
snd_rawmidi            24901  1 snd_usbmidi_lib
snd_seq_device          5142  1 snd_rawmidi
snd_pcm                93037  1 snd_usb_audio
snd_timer              24444  1 snd_pcm
snd_hwdep               6359  1 snd_usb_audio
snd                    68803  7 snd_usb_audio,snd_usbmidi_lib,snd_rawmidi,snd_seq_device,snd_pcm,snd_timer,snd_hwdep

Any idea what's going on?

Greetings,
   Gerrelt.
my Raspberry Pi page: http://raspberry.gerrelt.nl

Offline jncl

  • WikiUser
  • *
  • Posts: 38
Re: piCore-7.1beta2 released
« Reply #4 on: March 18, 2016, 04:16:56 PM »
Hi Gerrelt,

  What does the output of dmesg look like in respect to the dongle. Can you boot without it and then insert it and post what is reported in dmesg please.

Cheers

  Jon

Online bmarkus

  • Administrator
  • Hero Member
  • *****
  • Posts: 6908
    • My Community Forum
Re: piCore-7.1beta2 released
« Reply #5 on: March 18, 2016, 11:38:32 PM »
@Gerrelt

Does WiFi work with 7.1beta1?

I have a HTC 9271, firmware and at kernel moduels are loaded during boot correctley.
Béla
Ham Radio callsign: HA5DI

"Amateur Radio: The First Technology-Based Social Network."

Offline Gerrelt

  • Full Member
  • ***
  • Posts: 176
Re: piCore-7.1beta2 released
« Reply #6 on: March 19, 2016, 01:43:09 AM »
  What does the output of dmesg look like in respect to the dongle. Can you boot without it and then insert it and post what is reported in dmesg please.

Hi Jon,

This is the dmesg after inserting the WiFi adapter:

Code: [Select]
[   28.165694] uio: disagrees about version of symbol module_layout
[   28.177003] uio: disagrees about version of symbol module_layout
[   28.201891] uio: disagrees about version of symbol module_layout
[   28.207188] uio: disagrees about version of symbol module_layout
[   28.208993] regmap_mmio: disagrees about version of symbol module_layout
[   28.213141] uio: disagrees about version of symbol module_layout
[   28.226332] bcm2835_gpiomem: disagrees about version of symbol module_layout
[   28.230610] uio: disagrees about version of symbol module_layout
[   28.233131] i2c_bcm2708: disagrees about version of symbol module_layout
[   28.240622] i2c_bcm2708: disagrees about version of symbol module_layout
[   28.245209] spi_bcm2835: disagrees about version of symbol module_layout
[   28.440125] evdev: disagrees about version of symbol module_layout
[  748.904834] usb 1-1.3.5: new high-speed USB device number 7 using dwc_otg
[  749.135459] usb 1-1.3.5: New USB device found, idVendor=148f, idProduct=7601
[  749.135498] usb 1-1.3.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  749.135518] usb 1-1.3.5: Product: 802.11 n WLAN
[  749.135536] usb 1-1.3.5: SerialNumber: 1.0
[  749.182344] rfkill: disagrees about version of symbol module_layout

It disagrees a lot with the symbol module_layout..

Does WiFi work with 7.1beta1?

Hi Béla,

I've just tested it, and: yes, it "kind of" works with 7.1beta1.
The wlan01 network interface is now present when I execute the "iwconfig" command. Executing the wifi.sh script does also produce a list of WiFi SSID's.
But I cannot connect to my SSID. While trying to connect is throws (among the other output lines), this error:
Code: [Select]
sh: wpa_passphrase: not found
Also, I saw an error while installing wifi.tcz. It reports an checksum error on libn1.tcz:

Code: [Select]
tc@box:~$ tce-load -wi wifi.tcz
wifi.tcz.dep OK
wireless_tools.tcz.dep OK
wpa_supplicant.tcz.dep OK
readline.tcz.dep OK
Downloading: wireless-4.1.18-piCore+.tcz
Connecting to repo.tinycorelinux.net (89.22.99.37:80)
wireless-4.1.18-piCo 100% |*******************************************************************************************|  2624k  0:00:00 ETA
wireless-4.1.18-piCore+.tcz: OK
Downloading: libiw.tcz
Connecting to repo.tinycorelinux.net (89.22.99.37:80)
libiw.tcz            100% |*******************************************************************************************| 16384   0:00:00 ETA
libiw.tcz: OK
Downloading: wireless_tools.tcz
Connecting to repo.tinycorelinux.net (89.22.99.37:80)
wireless_tools.tcz   100% |*******************************************************************************************| 49152   0:00:00 ETA
wireless_tools.tcz: OK
Downloading: readline.tcz
Connecting to repo.tinycorelinux.net (89.22.99.37:80)
readline.tcz         100% |*******************************************************************************************|   116k  0:00:00 ETA
readline.tcz: OK
Downloading: libnl.tcz
Connecting to repo.tinycorelinux.net (89.22.99.37:80)
wget: short write
libnl.tcz: FAILED
md5sum: WARNING: 1 of 1 computed checksums did NOT match
Error on libnl.tcz

Greetings,
    Gerrelt.
my Raspberry Pi page: http://raspberry.gerrelt.nl

Offline Rich

  • TinyCore Moderator
  • Hero Member
  • *****
  • Posts: 5430
Re: piCore-7.1beta2 released
« Reply #7 on: March 19, 2016, 07:36:28 AM »
Hi Gerrelt
I don't think there's any md5 problem with libnl:
Code: [Select]
tc@box:~/guilib/picmanip$ wget http://tinycorelinux.net/7.x/armv6/tcz/libnl.tcz
--2016-03-19 11:26:54--  http://tinycorelinux.net/7.x/armv6/tcz/libnl.tcz
Resolving tinycorelinux.net... 89.22.99.37
Connecting to tinycorelinux.net|89.22.99.37|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 299008 (292K) [application/octet-stream]
Saving to: `libnl.tcz'

100%[================================================================================>] 299,008      589K/s   in 0.5s   

2016-03-19 11:26:55 (589 KB/s) - `libnl.tcz' saved [299008/299008]

tc@box:~/guilib/picmanip$ wget http://tinycorelinux.net/7.x/armv6/tcz/libnl.tcz.md5.txt
--2016-03-19 11:27:15--  http://tinycorelinux.net/7.x/armv6/tcz/libnl.tcz.md5.txt
Resolving tinycorelinux.net... 89.22.99.37
Connecting to tinycorelinux.net|89.22.99.37|:80... connected.
HTTP request sent, awaiting response... 200 OK
Length: 44 [text/plain]
Saving to: `libnl.tcz.md5.txt'

100%[================================================================================>] 44          --.-K/s   in 0s     

2016-03-19 11:27:15 (1.77 MB/s) - `libnl.tcz.md5.txt' saved [44/44]

tc@box:~/guilib/picmanip$ md5sum -c libnl.tcz.md5.txt
libnl.tcz: OK
tc@box:~/guilib/picmanip$

Maybe this is your problem:
Code: [Select]
Connecting to repo.tinycorelinux.net (89.22.99.37:80)
wget: short write
libnl.tcz: FAILED
Isn't  short write  an indication your disk is full?

Offline jncl

  • WikiUser
  • *
  • Posts: 38
Re: piCore-7.1beta2 released
« Reply #8 on: March 19, 2016, 07:48:06 AM »
Hi Béla,

  I can confirm that all the WiFi dongles I have tried on 7.1beta1 work.

  These include the following Vendor/Product pairs: 0x0bda/0x8176, 0xbda/0x8178, 0x0bda/0x8179, 0x148f/0x5370, 0x148f/0x7601, 0x148f/0x760b, 0x0a5c/0xbd1e.

  I can also confirm that all RPi's, running 7.1beta2, that have
Code: [Select]
disagrees about version of symbol module_layoutmessages also have just the header displayed when running lsmod
Code: [Select]
Module                  Size  Used by    Not tainted and furthermore Wifi modules aren't loaded on any of these.

HTH
  Jon
« Last Edit: March 19, 2016, 07:49:37 AM by jncl »

Online bmarkus

  • Administrator
  • Hero Member
  • *****
  • Posts: 6908
    • My Community Forum
Re: piCore-7.1beta2 released
« Reply #9 on: March 19, 2016, 08:02:04 AM »
Did you try a clean beta2 install?
Béla
Ham Radio callsign: HA5DI

"Amateur Radio: The First Technology-Based Social Network."

Offline jncl

  • WikiUser
  • *
  • Posts: 38
Re: piCore-7.1beta2 released
« Reply #10 on: March 19, 2016, 10:29:54 AM »
Hi Béla,

  On a clean 7.1beta2 install, I have found that the following WiFi dongles don't work with the current wireless* and firmware* extensions: 0x148f/0x7601, 0x148f/0x760b, 0x0a5c/0xbd1e. All the other ones mentioned in my previous post do work.

  lsmod only reports the WiFi module(s), no other ones are reported as loaded.

HTH

  Jon
« Last Edit: March 19, 2016, 10:31:27 AM by jncl »

Offline Gerrelt

  • Full Member
  • ***
  • Posts: 176
Re: piCore-7.1beta2 released
« Reply #11 on: March 19, 2016, 02:15:53 PM »
Hi Gerrelt
I don't think there's any md5 problem with libnl:
...
Maybe this is your problem:
Code: [Select]
Connecting to repo.tinycorelinux.net (89.22.99.37:80)
wget: short write
libnl.tcz: FAILED
Isn't  short write  an indication your disk is full?

D'oh... :-[  ...I made a rookie mistake, I forgot to enlarge the partition! You're totally right.
I will test again tomorrow.

Greetings,
   Gerrelt.
my Raspberry Pi page: http://raspberry.gerrelt.nl

Offline gavinmc42

  • Sr. Member
  • ****
  • Posts: 280
Re: piCore-7.1beta2 released
« Reply #12 on: March 19, 2016, 07:07:27 PM »
Trying to get wifi working on Pi3,

Got this in dmesg, which I assume means it does not know which country it is in.

[  349.348987] cfg80211: Calling CRDA to update world regulatory domain
[  352.508990] cfg80211: Exceeded CRDA call max attempts. Not calling CRDA

Installed iw.tcz
"iw reg get" gets this this

country 00: DFS-UNSET
   (2402 - 2472 @ 40), (6, 20), (N/A)
   (2457 - 2482 @ 40), (6, 20), (N/A), PASSIVE-SCAN
   (2474 - 2494 @ 20), (6, 20), (N/A), NO-OFDM, PASSIVE-SCAN
   (5170 - 5250 @ 160), (6, 20), (N/A), PASSIVE-SCAN
   (5250 - 5330 @ 160), (6, 20), (0 ms), DFS, PASSIVE-SCAN
   (5490 - 5730 @ 160), (6, 20), (0 ms), DFS, PASSIVE-SCAN
   (5735 - 5835 @ 80), (6, 20), (N/A), PASSIVE-SCAN
   (57240 - 63720 @ 2160), (N/A, 0), (N/A)

"sudo iw reg set AU" does not seem to work.

On my Linux Mint box I get this

country AU:
   (2402 - 2482 @ 40), (N/A, 20)
   (5170 - 5250 @ 40), (3, 23)
   (5250 - 5330 @ 40), (3, 23), DFS
   (5735 - 5835 @ 40), (3, 30)

'lsmod" gives this

Module                  Size  Used by    Not tainted
i2c_dev                 6020  0
brcmfmac              178949  0
brcmutil                5731  1 brcmfmac
cfg80211              436630  1 brcmfmac
rfkill                 16625  1 cfg80211
i2c_bcm2708             5002  0
bcm2835_gpiomem         3023  0
bcm2835_rng             1816  0
spi_bcm2835             7252  0
uio_pdrv_genirq         2966  0
uio                     8340  1 uio_pdrv_genirq

'iwconfig"

wlan0     IEEE 802.11bgn  ESSID:off/any 
          Mode:Managed  Access Point: Not-Associated   
          Retry short limit:7   RTS thr:off   Fragment thr:off
          Power Management:on
         
lo        no wireless extensions.

eth0      no wireless extensions.

installing and running "strace sudo iw reg set AU" give a bunch of stuff but this bit sticks out

open("/sys/class/ieee80211/reg/index", O_RDONLY) = -1 ENOENT (No such file or directory)
sendmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"\34\0\0\0\26\0\5\0\242\16\356V3\4@\25\33\0\0\0\7\0!\0AU\0\0", 28}], msg_controllen=0, msg_flags=0}, 0) = 28
recvmsg(3, {msg_name(12)={sa_family=AF_NETLINK, pid=0, groups=00000000}, msg_iov(1)=[{"0\0\0\0\2\0\0\0\242\16\356V3\4@\25\377\377\377\377\34\0\0\0\26\0\5\0\242\16\356V"..., 16384}], msg_controllen=0, msg_flags=0}, 0) = 48
write(2, "command failed: Operation not pe"..., 45command failed: Operation not permitted (-1)
) = 45
close(3)

google says hostapd needed?

tce-load -wi hostapd.tcz
hostapd.tcz.dep OK
Downloading: openssl-1.0.1.tcz
Connecting to repo.tinycorelinux.net (89.22.99.37:80)
openssl-1.0.1.tcz    100% |****************************************************|  1520k  0:00:00 ETA
openssl-1.0.1.tcz: OK
Downloading: libnl1.tcz
Connecting to repo.tinycorelinux.net (89.22.99.37:80)
wget: server returned error: HTTP/1.1 404 Not Found
md5sum: libnl1.tcz.md5.txt: No such file or directory
Error on libnl1.tcz

No clues what to do next, but I think that is also the wrong openssl version, current is 1.0.2?

Offline Gerrelt

  • Full Member
  • ***
  • Posts: 176
Re: piCore-7.1beta2 released
« Reply #13 on: March 20, 2016, 01:10:38 AM »
@Gerrelt

Does WiFi work with 7.1beta1?

Hi Béla,

I've retested and I can now confirm it's working perfectly on 7.1beta1.

Greetings,
   Gerrelt.
my Raspberry Pi page: http://raspberry.gerrelt.nl

Online bmarkus

  • Administrator
  • Hero Member
  • *****
  • Posts: 6908
    • My Community Forum
Re: piCore-7.1beta2 released
« Reply #14 on: March 20, 2016, 01:45:26 AM »
Thanks, let's see beta3 in next days
Béla
Ham Radio callsign: HA5DI

"Amateur Radio: The First Technology-Based Social Network."