WelcomeWelcome | FAQFAQ | DownloadsDownloads | WikiWiki

Author Topic: md5sum: bash.tcz.md5.txt: No such file or directory (piCore-6.1, armv7, RPi 2)  (Read 3664 times)

Offline paperone

  • Newbie
  • *
  • Posts: 19
I got the following error when I tried to install bash.tcz on piCore-6.1_v7-X in RPi 2 B:
wget: short write
md5sum: bash.tcz.md5.txt: No such file or directory
Error on bash.tcz


I am able to install other extensions alright, any idea why bash.tcz keeps failing on me?
« Last Edit: November 25, 2015, 12:59:58 AM by paperone »
Hello from sunny Singapore! :)

Offline curaga

  • Administrator
  • Hero Member
  • *****
  • Posts: 10957
Short write means you ran out of space.
The only barriers that can stop you are the ones you create yourself.

Offline bmarkus

  • Administrator
  • Hero Member
  • *****
  • Posts: 7183
    • My Community Forum
Did you expand the partition as described in README?
Béla
Ham Radio callsign: HA5DI

"Amateur Radio: The First Technology-Based Social Network."

Offline paperone

  • Newbie
  • *
  • Posts: 19
Hm. I always expand the partition first thing when I boot up piCore for the first time. Maybe it was my other mistake, I will try expanding the partition again and see if it work.
Thank you guys!
Hello from sunny Singapore! :)

Offline paperone

  • Newbie
  • *
  • Posts: 19
I think I have found the issue but not yet a fix. Right after I wrote the image file (piCore-6.1_v7-X.img) to micro SD Card, I boot it up using a Raspberry Pi 2 Model B:

Code: [Select]
tc@box:~$ sudo fdisk /dev/mmcblk0

The number of cylinders for this disk is set to 493536.
There is nothing wrong with that, but this is larger than 1024,
and could in certain setups cause problems with:
1) software that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
   (e.g., DOS FDISK, OS/2 FDISK)

Command (m for help): p

Disk /dev/mmcblk0: 16.1 GB, 16172187648 bytes
4 heads, 16 sectors/track, 493536 cylinders
Units = cylinders of 64 * 512 = 32768 bytes

        Device Boot      Start         End      Blocks  Id System
/dev/mmcblk0p1             129         768       20480   c Win95 FAT32 (LBA)
Partition 1 does not end on cylinder boundary
/dev/mmcblk0p2             769        1632       27648  83 Linux
Partition 2 does not end on cylinder boundary

Command (m for help): d
Partition number (1-4): 2

Command (m for help): n
Command action
   e   extended
   p   primary partition (1-4)
p
Partition number (1-4): 2
First cylinder (1-493536, default 1): 769
Last cylinder or +size or +sizeM or +sizeK (769-493536, default 493536): Using default value 493536

Command (m for help): w
The partition table has been altered.
Calling ioctl() to re-read partition table
fdisk: WARNING: rereading partition table failed, kernel still uses old table: Device or resource busy

Then I rebooted the system and did a resize2fs command:

Code: [Select]
tc@box:~$ sudo resize2fs /dev/mmcblk0p2
resize2fs 1.42.13 (17-May-2015)
Filesystem at /dev/mmcblk0p2 is mounted on /mnt/mmcblk0p2; on-line resizing required
old_desc_blocks = 1, new_desc_blocks = 61
resize2fs: No space left on device While checking for on-line resizing support
tc@box:~$

I see that there are 2 warning at the end of fdisk and resize2fs command. I had used the micro SD card for:
  • Raspbian on Raspberry Pi 1 Model B without issue.
  • piCore 6.0-X (armv6) on Raspberry Pi 1 Model B also without issue.
  • piCore 6.1 v7-X (armv7) on Raspberry Pi 2 Model B, this is when I tried to expand the partition 2 and got the error above.

Any idea?
Hello from sunny Singapore! :)

Offline bmarkus

  • Administrator
  • Hero Member
  • *****
  • Posts: 7183
    • My Community Forum
Did you try offline resizing?
Béla
Ham Radio callsign: HA5DI

"Amateur Radio: The First Technology-Based Social Network."

Offline bmarkus

  • Administrator
  • Hero Member
  • *****
  • Posts: 7183
    • My Community Forum
I kindly advice to use piCore-7.0beta1
Béla
Ham Radio callsign: HA5DI

"Amateur Radio: The First Technology-Based Social Network."

Offline paperone

  • Newbie
  • *
  • Posts: 19
I kindly advice to use piCore-7.0beta1

Got it Marcus, I will try piCore 7.0beta1! Thank you!  :)
Hello from sunny Singapore! :)